The command-line flags --plt and --collection-plt direct mzc to create an archive for distributing files to PLT users. A distribution archive usually has the suffix .plt, which Help Desk and DrScheme recognize as archives to provide automatic unpacking facilities. The Setup PLT program also supports .plt unpacking.
An archive contains the following elements:
a set of files and directories to be unpacked, and a flag indicating whether they are always to be unpacked relative to the PLT installation directory. The files and directories for an archive are provided on the command line to mzc, either directly with --plt or in the form of collection names with --collection-plt. In the latter case, the files are unpacked relative to the PLT installation directory.
a flag for each file indicating whether it overwrites an existing file when the archive is unpacked; the default is to leave the old file in place, but mzc's --replace flag enables replacing for all files in the archive.
a list of collections to be set-up (via Setup PLT) after the archive is unpacked; mzc's ++setup flag adds a collection name to the archive's list, but each collection for --collection-plt is added automatically.
a list of required collections (with associated version numbers) and a list of conflicting collections; mzc always names the mzscheme collection in the required list (using the collection's pack-time version), mzc names each packed collection in the conflict list (so that a collection is not unpacked on top of a different version of the same collection), and mzc extracts other requirements and conflicts from the info.ss files of collections for --collection-plt.
Use the --plt flag to specify individual directories and files for the archive. Each file and directory must be specified with a relative path. By default, if the archive is unpacked with Help Desk or DrScheme, the user will be prompted for a target directory, and if Setup PLT is used to unpack the archive, the files and directories will be unpacked relative to the current directory. If the --at-plt flag is provided to mzc, the files and directories will be unpacked relative to the PLT installation directory, instead.
Use the --collection-plt flag to pack one or more collections; sub-collections can be designated by using a forward slash (``/'') as a path separator on all platforms. In this mode, mzc automatically uses paths relative to the PLT installation directory for the archived files, and the collections will be set-up after unpacking. In addition, mzc consults each collection's info.ss file, as described below, to determine the set of required and conflicting collections. Finally, mzc consults the first collection's info.ss file to obtain a default name for the archive. For example, the following command creates a sirmail.plt archive for distributing a sirmail collection:
mzc --collection-plt sirmail.plt sirmail
When packing collections, mzc checks the following fields of each collection's info.ss file (see section 7):
requires -- a list of the form
( where each
coll-path vers) ···)
coll-path is a non-empty
list of relative-path strings, and each
vers is a (possibly
empty) list of exact integers. The indicated collections must be
installed at unpacking time, with version sequences that match as
much of the version sequence specified in the corresponding
A collection's version is indicated by a
version field in
it's info.ss file, and the defalt version is the empty list.
The version sequence generalized major and minor version numbers. For
'(2 5 4 7) of a collection can be used when
'(2 5 4 7) is required.
conflicts -- a list of the form
( where each
coll-path is a non-empty list of
relative-path strings. The inidicated collections must not be
installed at unpacking time.
For example, the info.ss file in the sirmail collection
might contain the following
(module info (lib "infotab.ss" "setup") (define name "SirMail") (define mred-launcher-libraries (
list"sirmail.ss")) (define mred-launcher-names (
list"SirMail")) (define requires (
Then, the sirmail.plt file (created by the command-line example above) will contain the name ``SirMail''. When the archive is unpacked, the unpacker will check that the MrEd collection is installed (not just MzScheme), and that MrEd has the same version as when sirmail.plt was created.
Although mzc's command-line interface is sufficient for most purposes, the pack.ss library of the setup collection provides a general interface for constructing archives.