The library installs a Readline-based input port, and hooks the prompt-and-read part of MzScheme’s read-eval-print-loop to interact with it
You can start MzScheme with
mzscheme -il readline
in the MzScheme read-eval-print-loop to load Readline manually. You can also put (require readline) in your "~/.mzschemerc", so that MzScheme automatically loads Readline support in interactive mode.
If you want to enable Readline support only sometimes – such as only when you use an xterm, and not when you use an Emacs shell – then you can use dynamic-require, as in the following example:
(dynamic-require 'readline #f))
The library automatically checks whether the current input port is a terminal, as determined by terminal-port?, and it installs Readline only to replace terminal ports. The readline/rep-start module installs Readline without a terminal check.
By default, Readline’s completion is set to use the visible bindings in the current namespace. This is far from ideal, but it’s better than Readline’s default filename completion which is rarely useful. In addition, the Readline history is stored across invocations in MzScheme’s preferences file, assuming that MzScheme exits normally.
Adds (require readline) to the result of (find-system-path 'init-file), which is "~/.mzschemerc" under Unix. Consequently, Readline will be loaded whenever MzScheme is started in interactive mode. The declaration is added only if it is not already present, as determined by reading and checking all top-level expressions in the file. For more fine-grained control, such as conditionally loading Readline based on an environment variable, edit "~/.mzschemerc" manually.
The readline/pread library provides customization, and support for prompt-reading after installs the new input port.
The reading facility that the new input port provides can be customized with the following parameters.
bstr : bytes?
A parameter that determines the prompt that is used, as a byte string. Defaults to #"> ".
on? : any/c
A parameter. If #f, no prompt is shown until you write input that is completely readable. For example, when you type
(foo bar) (+ 1
you will see a single prompt in the beginning.
The problem is that the first expression can be (read-line), which normally consumes the rest of the text on the same line. The default value of this parameter is therefore #t, making it mimic plain I/O interactions.
(max-history) → nonnegative-exact-integer?
n : nonnegative-exact-integer?
A parameter that determines the number of history entries to save, defaults to 100.
keep? : any/c
A parameter. If #f (the default), then lines that are equal to the previous one are not added as new history items.
keep? : any/c
A parameter. If #f (the default), blank input lines are not kept in history.
The new input port that you get when you require is a custom port that uses Readline for all inputs. The problem is when you want to display a prompt and then read some input, Readline will get confused if it is not used when the cursor is at the beginning of the line (which is why it has a prompt argument.) To use this prompt:
This expression makes the first call to Readline use the prompt, and subsequent calls will use an all-spaces prompt of the same length (for example, when you’re reading an S-expression). The normal value of readline-prompt is #f for an empty prompt (and spaces after the prompt is used, which is why you should use parameterize to restore it to #f).
A proper solution would be to install a custom output port, too, which keeps track of text that is displayed without a trailing newline. As a cheaper solution, if line-counting is enabled for the terminal’s output-port, then a newline is printed before reading if the column is not 0. (The library enables line-counting for the output port.)
Warning: The Readline library uses the output port directly. You should not use it when current-input-port has been modified, or when it was not a terminal port when MzScheme was started (eg, when reading input from a pipe). Expect some problems if you ignore this warning (not too bad, mostly problems with detecting an EOF).
prompt : string?
Prints the given prompt string and reads a line.
prompt : bytes?
Like readline, but using raw byte-strings for the prompt and returning a byte string.
str : string?
Adds the given string to the Readline history, which is accessible to the user via the up-arrow key.
str : string?
Adds the given byte string to the Readline history, which is accessible to the user via the up-arrow key.
Sets Readline’s rl_completion_entry_function to proc. The type argument, whose possible values are from scheme/foreign, determines the type of value supplied to the proc.
GNU’s Readline library is covered by the GPL, and that applies to code that links with it. PLT Scheme is LGPL, so this code is not used by default; you should explicitly enable it if you want to. Also, be aware that if you write code that uses this library, it will make your code link to the Readline library when invoked, with the usual GPL implications.