On this page:
flush-output
file-stream-buffer-mode
file-position
Version: 4.2.1
12.1.3 Port Buffers and Positions

Some ports – especially those that read from and write to files – are internally buffered:

If a port supports buffering, its buffer mode can be changed via file-stream-buffer-mode (even if the port is not a file-stream port).

For an input port, peeking always places peeked bytes into the port’s buffer, even when the port’s buffer mode is 'none; furthermore, on some platforms, testing the port for input (via char-ready? or sync) may be implemented with a peek. If an input port’s buffer mode is 'none, then at most one byte is read for read-bytes-avail!*, read-bytes-avail!, peek-bytes-avail!*, or peek-bytes-avail!; if any bytes are buffered in the port (e.g., to satisfy a previous peek), the procedures may access multiple buffered bytes, but no further bytes are read.

In addition, the initial current output and error ports are automatically flushed when read, read-line, read-bytes, read-string, etc. are performed on the initial standard input port; more precisely, flushing is performed by the default port read handler (see port-read-handler).

(flush-output [out])  void?
  out : output-port? = (current-output-port)
Forces all buffered data in the given output port to be physically written. Only file-stream ports, TCP ports, and custom ports (see Custom Ports) use buffers; when called on a port without a buffer, flush-output has no effect.

(file-stream-buffer-mode port)  (or/c 'none 'line 'block #f)
  port : port?
(file-stream-buffer-mode port mode)  void?
  port : port?
  mode : (or/c 'none 'line 'block)
Gets or sets the buffer mode for port, if possible. File-stream ports support setting the buffer mode, TCP ports (see Networking) support setting and getting the buffer mode, and custom ports (see Custom Ports) may support getting and setting buffer modes.

If mode is provided, it must be one of 'none, 'line (output only), or 'block, and the port’s buffering is set accordingly. If the port does not support setting the mode, the exn:fail exception is raised.

If mode is not provided, the current mode is returned, or #f is returned if the mode cannot be determined. If file-stream-port is an input port and mode is 'line, the exn:fail:contract exception is raised.

(file-position port)  exact-nonnegative-integer?
  port : port?
(file-position port pos)  void?
  port : port?
  pos : (or/c exact-nonnegative-integer? eof-object?)
Returns or sets the current read/write position of port.

Calling file-position without a position on a non-file/non-string input port returns the number of bytes that have been read from that port if the position is known (see Counting Positions, Lines, and Columns), otherwise the exn:fail:filesystem exception is raised.

For file-stream ports and string ports, the position-setting variants sets the read/write position to pos relative to the beginning of the file/string if pos is a number, or to the current end of the file/string if pos is eof. In position-setting mode, file-position raises the exn:fail:contract exception for port kinds other than file-stream and string ports. Furthermore, not all file-stream ports support setting the position; f file-position is called with a position argument on such a file-stream port, the exn:fail:filesystem exception is raised.

When file-position sets the position pos beyond the current size of an output file or string, the file/string is enlarged to size pos and the new region is filled with 0 bytes. If pos is beyond the end of an input file or string, then reading thereafter returns eof without changing the port’s position.

When changing the file position for an output port, the port is first flushed if its buffer is not empty. Similarly, setting the position for an input port clears the port’s buffer (even if the new position is the same as the old position). However, although input and output ports produced by open-input-output-file share the file position, setting the position via one port does not flush the other port’s buffer.